Tech Tip: How To Install Gibson Pickups In Epiphone Guitars

Tech Tip: How to Install Gibson Pickups in Epiphone Guitars

Posted on .

Hot Rod your Epiphone with Genuine Gibson Pickups. Do It Yourself!

By Mikey Lank

Among the greatest things about Gibson electric guitars are Gibson pickups. One of the coolest things about Epiphone guitars is that they're almost all made with Gibson body styles and dimensions. That means that with out modifications you can replace your Epiphone pickups with genuine Gibson pickups. The result can be astonishing. Check out my Hands-On Review of Gibson USA-Made Pickups to read how blown away I was by such magnetic monsters as the Tony Iommi, Dirty Fingers, the '57 Classic, Burstbucker Pro, and others. Each of these pickups transformed a garden-variety Epi LP Junior into a heavyweight tone machine.

Changing out your guitar's pickups is so simple you can do it yourself. All you need is a soldering iron and some rosin-core solder, a Phillips Head screwdriver, and a wire stripper. It's a fully reversible operation; I installed, extensively tested, and changed out six pickups in the same guitar in one afternoon with no mishaps. If you're solder-phobic, you can have your new pickup put in at your local guitar shop for a modest fee. But even if you've never used a soldering iron you shouldn't have any problem, it's basically just tacking a couple of wires to a pot. Now let's get down to it.

Epiphone Les Paul Guitar

Step 1

We'll use an Epiphone Les Paul as our example. Refresh your memory on the controls. Looking at the guitar held in playing position, the top row of knobs are the volume and tone controls for the rhythm (neck) pickup. The knob closest to the neck is the volume control. The lower row of knobs controls the volume and tone for the treble (bridge) pickup. First remove the strings, bridge, and tailpiece.

Removing Back Plate of an Epiphone Les Paul

Step 2

Then place the guitar face down on a non-scratching surface and remove the back plate behind the knobs. Don't try to use the wrong size of screwdriver, you'll strip the screws and have a bad day. Leave the round plate alone, that's just for the toggle switch, which we're not changing.

Epiphone Les Paul Pickup Connections

Step 3

When the back plate is removed, you should see something like this (see image). If you have a digital camera, take a picture of the open cavity for future reference. The volume pots--the ones we'll be concerned with here--are the two on the left, rhythm pickup on top and treble pickup on the bottom. On the rhythm pickup volume pot, there should be a red wire with the shield connected to the back of the pot and the inside connected to the first lug on the bottom of the pot. There is a similar arrangement on the treble pickup volume pot except the wire is black. (The colors may vary depending on the guitar you're working on. The hot wire is the one connected to the lug.) These are the pickup connections.

Unsolder and remove epiphone pickup wires

Step 4

Carefully unsolder and remove these wires. Do not cut the wires, just touch the soldering iron to the solder joint while very gently pulling on the wire. The wire will come off as soon as the solder melts. Leave the blobs of solder on the backs of the pots. If there's enough there, you won't have to use additional solder later.


Remove screws from pickup bezel

Step 5

After the pickup leads are loose, flip the guitar back over, remove the four corner screws from the pickup bezel.



Remove Epiphone Pickup Assembly

Step 6

Lift the whole pickup assembly out. Grasp the pickup lead and gently pull it out through the tunnel in the body, entirely freeing the pickup from the instrument.




Remove Epiphone Pickup from Bezel

Step 7

Remove the pickup from the bezel by taking out the two spring-loaded screws on the side.



Mounting Gibson Pickup on Epiphone Bezel

Step 8

Mount the new pickup in the bezel by reversing the process using the new screws that came with your pickup. With the spring tension on it, threading the new screw in the pickup can be a little tricky, but with persistence you'll get it.


Thread the New Pickup Cable & Cut to Length

Step 9

Thread the new pickup cable through the tunnel to the pot cavity. Cut the new pickup cable to the length of the old pickup cable or coil it neatly in the pot cavity. All that's left to do now is to strip and prepare the new leads and solder them in place the same way the old ones were. Use your picture as a reference. (You did take a picture, didn't you?)

Vintage Two-Conductor Wiring

Step 10A: Vintage two-conductor wiring

Gibson '57 Classic, '57 Classic Plus, P-90, and P-100 pickups all feature vintage two-conductor wiring. These pickups are very simple to install. Skin back the shield (wire mesh) to reveal the hot lead wire. Strip the end of the hot wire back 1/8" using your wire stripper or a razor blade. "Tin" the wire by touching the tip of the soldering iron to the exposed lead wire and applying a little solder to soak in between the strands. Don't try to skip this step, it makes the rest of the job much easier.

Twist the fibers of the shield together to make a separate ground lead and tin this lead as well. Solder the hot lead wire to the right-hand lower terminal (the one the hot lead from the old pickup was attached to) by putting the iron on the terminal, melting solder on the terminal, and slipping the end of the lead wire through the hole in the terminal. Add more solder if needed. Very gently tug on the wire to be sure it's secure.

Solder the shield wire to the back of the case of the pot by heating the pot with the iron and using a flathead screwdriver to hold the wire down while adding solder. If there's a good-sized blob of solder from the old shield, that should be enough. Again, tug lightly on the wire to be sure you've made a solid connection.

Standard Four-Lead Wiring

Step 10B: Standard four-lead wiring

Most Gibson humbuckers feature four-lead wiring to enable coil splitting (using only one coil of the dual-coil humbucker). If you're not going to enable coil splitting (which you probably won't for a Les Paul), these pickups are almost as easy to install as two-lead pickups. The green and white wires are for coil splitting; just solder them together, put a piece of electrical tape over them, and forget about them. The red wire is the hot lead. Tin it and solder it to the terminal. Twist the black wire and the bare wire together, tin them, and solder them to the pot casing.

If you want to use the coil-splitting function (also called coil tapping), each Gibson pickup comes with a wiring diagram under the foil lining of the box to help you install it.

That's it!

After you install both pickups, carefully inspect your work to make sure the solder joints are clean and shiny and that there are no stray wires. Before closing the pot cavity, plug the guitar into an amp and tap the new pickup's pole pieces with a screwdriver. If the connection is right, you'll hear the tapping through the amp. Also check to be sure the volume control is working. Put your guitar back together and enjoy your wonderful new tone!

The simple process of changing out your pickups can transform your so-so axe into a tonal titan. Find the right model for your sound and give it a try--you won't be disappointed.

Tags: Pickups


# Dan miller 2016-02-11 19:26
What if you have the limited issue, plain,,, epiphone Gibson G400CH made in Korea in 1992 and you wants to install the two humbuckberer set (blue wire on neck humbucker and yellow wire on bridge humbucker) pre-wired FMC 4 pot with Jack and pickup kit.
Does anyone have experience wiring the FMC
# Mike Stone 2015-10-27 10:47
I have epi 2 p90s 1vol 1tone, swapping neck pup for humbucker 4 wire red white green black & braid it appears red south coil white north it has 3 way toggle saw and I feel I would like to coil split south coil only full hum only hum+p90 & p90 only. I have a coil tap pot if needed can you help me with this wiring configuration please Mike
# kyle carrington 2015-02-09 10:05
it turns out that it's not quite as simple as illustrated, in my example. I tried to put 2012 Gibson Les Paul Traditional pickups, which are a Gibson authentic 57 set, classic and Classic Plus... Into a 2003 Chinese made Epiphone Les Paul Plus top. The bolt diameter for the anchoring bolts is different so the swap is not immediate. Now I am left to purchase an entire set of gibson pickup rings to get the bolts, I guess... I only hope they come with the bolts... and not the opposite situation, in that the bolts are sold with the pickups....
# mike smith 2016-04-14 10:48
Kyle you went down a dark road, been there like many others. The screws and springs must match the pickups. If you don't have them you have to find them, and most are poorly labeled you might buy several sets before you get what you need. Off brands like all pro don't label the packages you just trust! I usually buy gibson rings with screws and springs in the same package just to make sure they fit a gibson pickup.
# Gene V 2014-08-06 06:07
I have a Gibson Les Paul Studio deluxe that I swapped neck pickups on. I tried to put the 490R in my Epi and the pickup brackets aren't the same height. Can these brackets be changed?
# mike smith 2016-04-14 10:39
Brackets are part of the pickup you don't change those. The pickups are different; and that means the screws and springs will be different too--so you should get a matching set with the pickups. Try to use the wrong screws and you will mess up the pickups.
# Butch C 2014-06-29 14:57
I have an epiphone les paul with the coil taps. i want to install a classic 57 in the neck and a 57 classic plus in the bridge, i cant find a classic plus with the 4 wire lead.
can i just change the 2 push pull pots to normal ones and install the pickups or is there more involved then that? thanks Butch
# Johnny V 2014-05-21 18:26
Will the Gibson vol and tone controls mounted to a PWB by Gibson, fit the vol and tone drilled pattern in an Epiphone without modifying the body?
# James 2014-05-03 07:32
good read but can you do a guide or email me a link about changing the pots and switch in an epiphone as well? thanks!
# Roger 2014-04-12 22:41
I have been playing guitar for over 45 years and love to hear vintage Gibson tonality. I just replaced by Epiphone Les Paul Model neck pickup with the BurstBucker 2 and Wow was I surprised at the tone. The instruction on how to replace the pickup was spot on. It made the job so easy and worth every minute of improving my sound. Thank you Gibson for making this awesome pickup. I would recommend this gear to fellow musicians. Rock On!
# Mark L 2014-02-20 09:55
Thank you for this wonderful and helpful tech tip. I am replacing the stock pickups on my Epiphone with Gibson Burstbuckers. The stock has standard 4-wire. The new PU has Vintage 2-wires. Would the steps be the same?

Add comment

Security code

The HUB by Musician's Friend Logo



Stupid Deal of the Day (SDOTD)   Open Box Musical Instruments at Musician's Friend


  • Guitar Case Finder
  • Give a Gift Certificate
  • Clearance
  • Private Reserve Guitars


  • Hot Deals
  • On Sale
  • Pre-Order the Latest Gear
  • New Gear
  • Top Rated Gear